Send Message
Home > products > MCU Microcontroller Unit > AT91SAM7S64-AU-001 optical integrated circuits Integrated Circuit Chip AT91 ARM Thumb-based Microcontrollers

AT91SAM7S64-AU-001 optical integrated circuits Integrated Circuit Chip AT91 ARM Thumb-based Microcontrollers

manufacturer:
Manufacturer
Description:
ARM7® SAM7S Microcontroller IC 16/32-Bit 55MHz 64KB (64K x 8) FLASH 64-LQFP (10x10)
Category:
MCU Microcontroller Unit
Price:
Negotiate
Payment Method:
T/T, Western Union, Paypal
Specifications
Voltage And ADC Regulator Power Supply Input:
3.0 To 3.6V
Voltage Regulator Output:
1.85V Nominal
Flash Power Supply:
3.0V To 3.6V
I/O Lines Power Supply:
3.0V To 3.6V Or 1.65V To 1.95V
Core Power Supply:
1.65V To 1.95V
PLL:
1.65V To 1.95V
Highlight:

electronic integrated circuit

,

digital integrated circuits

Introduction

 

AT91 ARM Thumb-based Microcontrollers

AT91SAM7S512 AT91SAM7S256 AT91SAM7S128 AT91SAM7S64 AT91SAM7S321 AT91SAM7S32 AT91SAM7S161 AT91SAM7S16

 

Features

• Incorporates the ARM7TDMI® ARM® Thumb® Processor

  – High-performance 32-bit RISC Architecture

  – High-density 16-bit Instruction Set

  – Leader in MIPS/Watt

  – EmbeddedICE™ In-circuit Emulation, Debug Communication Channel Support

• Internal High-speed Flash

  – 512 Kbytes (AT91SAM7S512) Organized in Two Contiguous Banks of 1024 Pages of 256 Bytes

     (Dual Plane)

  – 256 Kbytes (AT91SAM7S256) Organized in 1024 Pages of 256 Bytes (Single Plane)

  – 128 Kbytes (AT91SAM7S128) Organized in 512 Pages of 256 Bytes (Single Plane)

  – 64 Kbytes (AT91SAM7S64) Organized in 512 Pages of 128 Bytes (Single Plane)

  – 32 Kbytes (AT91SAM7S321/32) Organized in 256 Pages of 128 Bytes (Single Plane)

  – 16 Kbytes (AT91SAM7S161/16 Organized in 256 Pages of 64 Bytes (Single Plane)

  – Single Cycle Access at Up to 30 MHz in Worst Case Conditions

  – Prefetch Buffer Optimizing Thumb Instruction Execution at Maximum Speed

  – Page Programming Time: 6 ms, Including Page Auto-erase, Full Erase Time: 15 ms

  – 10,000 Write Cycles, 10-year Data Retention Capability, Sector Lock Capabilities, Flash Security Bit

  – Fast Flash Programming Interface for High Volume Production

• Internal High-speed SRAM, Single-cycle Access at Maximum Speed

  – 64 Kbytes (AT91SAM7S512/256)

  – 32 Kbytes (AT91SAM7S128)

  – 16 Kbytes (AT91SAM7S64)

  – 8 Kbytes (AT91SAM7S321/32)

  – 4 Kbytes (AT91SAM7S161/16)

• Memory Controller (MC)

  – Embedded Flash Controller, Abort Status and Misalignment Detection

• Reset Controller (RSTC)

  – Based on Power-on Reset and Low-power Factory-calibrated Brown-out Detector

  – Provides External Reset Signal Shaping and Reset Source Status

• Clock Generator (CKGR)

  – Low-power RC Oscillator, 3 to 20 MHz On-chip Oscillator and one PLL

• Power Management Controller (PMC)

  – Software Power Optimization Capabilities, Including Slow Clock Mode (Down to 500 Hz) and Idle Mode

  – Three Programmable External Clock Signals

• Advanced Interrupt Controller (AIC)

  – Individually Maskable, Eight-level Priority, Vectored Interrupt Sources

  – Two (AT91SAM7S512/256/128/64/321/161) or One (AT91SAM7S32/16)

     External Interrupt Source(s) and One Fast Interrupt Source, Spurious Interrupt Protected

• Debug Unit (DBGU)

  – 2-wire UART and Support for Debug Communication Channel interrupt,

     Programmable ICE Access Prevention

  – Mode for General Purpose 2-wire UART Serial Communication

• Periodic Interval Timer (PIT)

  – 20-bit Programmable Counter plus 12-bit Interval Counter

• Windowed Watchdog (WDT)

  – 12-bit key-protected Programmable Counter

  – Provides Reset or Interrupt Signals to the System

  – Counter May Be Stopped While the Processor is in Debug State or in Idle Mode

• Real-time Timer (RTT)

  – 32-bit Free-running Counter with Alarm

  – Runs Off the Internal RC Oscillator

• One Parallel Input/Output Controller (PIOA)

  – Thirty-two (AT91SAM7S512/256/128/64/321/161) or twenty-one (AT91SAM7S32/16)

     Programmable I/O Lines Multiplexed with up to Two Peripheral I/Os

  – Input Change Interrupt Capability on Each I/O Line

  – Individually Programmable Open-drain, Pull-up resistor and Synchronous Output

• Eleven (AT91SAM7S512/256/128/64/321/161) or Nine (AT91SAM7S32/16) Peripheral DMA

  Controller (PDC) Channels

• One USB 2.0 Full Speed (12 Mbits per Second) Device Port (Except for the AT91SAM7S32/16).

  – On-chip Transceiver, 328-byte Configurable Integrated FIFOs

• One Synchronous Serial Controller (SSC)

  – Independent Clock and Frame Sync Signals for Each Receiver and Transmitter

  – I²S Analog Interface Support, Time Division Multiplex Support

  – High-speed Continuous Data Stream Capabilities with 32-bit Data Transfer

• Two (AT91SAM7S512/256/128/64/321/161) or One (AT91SAM7S32/16) Universal

  Synchronous/Asynchronous Receiver Transmitters (USART)

  – Individual Baud Rate Generator, IrDA® Infrared Modulation/Demodulation

  – Support for ISO7816 T0/T1 Smart Card, Hardware Handshaking, RS485 Support

  – Full Modem Line Support on USART1 (AT91SAM7S512/256/128/64/321/161)

• One Master/Slave Serial Peripheral Interface (SPI)

  – 8- to 16-bit Programmable Data LeCM GROUPh, Four External Peripheral Chip Selects

• One Three-channel 16-bit Timer/Counter (TC)

  – Three External Clock Input and Two Multi-purpose I/O Pins per Channel

     (AT91SAM7S512/256/128/64/321/161)

  – One External Clock Input and Two Multi-purpose I/O Pins for the first Two Channels Only

     (AT91SAM7S32/16)

  – Double PWM Generation, Capture/Waveform Mode, Up/Down Capability

• One Four-channel 16-bit PWM Controller (PWMC)

• One Two-wire Interface (TWI)

  – Master Mode Support Only, All Two-wire Atmel EEPROMs and I2 C Compatible Devices Supported

     (AT91SAM7S512/256/128/64/321/32)

  – Master, Multi-Master and Slave Mode Support, All Two-wire Atmel EEPROMs and I2 C Compatible

     Devices Supported (AT91SAM7S161/16)

• One 8-channel 10-bit Analog-to-Digital Converter, Four Channels Multiplexed with Digital I/Os

• SAM-BA™ Boot Assistant

  – Default Boot program

  – Interface with SAM-BA Graphic User Interface

• IEEE® 1149.1 JTAG Boundary Scan on All Digital Pins

• 5V-tolerant I/Os, including Four High-current Drive I/O lines, Up to 16 mA Each

  (AT91SAM7S161/16 I/Os Not 5V-tolerant)

• Power Supplies

  – Embedded 1.8V Regulator, Drawing up to 100 mA for the Core and External Components

  – 3.3V or 1.8V VDDIO I/O Lines Power Supply, Independent 3.3V VDDFLASH Flash Power Supply

  – 1.8V VDDCORE Core Power Supply with Brown-out Detector

• Fully Static Operation: Up to 55 MHz at 1.65V and 85⋅ C Worst Case Conditions

• Available in 64-lead LQFP Green or 64-pad QFN Green Package

  (AT91SAM7S512/256/128/64/321/161) and 48-lead LQFP Green or 48-pad QFN Green Package

  (AT91SAM7S32/16)

 

AT91SAM7S512/256/128/64/321/161 Block Diagram

 

 

AT91SAM7S32/16 Block Diagram

 

 

 

 

Stock Offer (Hot Sell)

Part no. Quantity Brand D/C Package
PC400 1999 SHARP 16+ SOP
2N5551 2000 ON 16+ TO-92
2SK2225 2000 RENESAS 13+ TO-3P
4N35 2000 VISHAY 15+ DIP6
74HC125D 2000 16+ SOP
ADXRS620BBGZ 2000 ADI 16+ GBA
AP40T03GS 2000 APEC 14+ TO-263
AT89C51-24PC 2000 ATMEL 14+ DIP40
BB405 2000 PH 14+ DO-34
BTA10-600B 2000 ST 16+ T0-220
BU2508DX 2000 PHI 16+ TO-3P
CA3420E 2000 INTERSIL 13+ DIP8
FQP4N90 2000 FSC 15+ TO-220
IRFP3710 2000 IR 16+ TO-247
IRFZ44NPBF 2000 IR 16+ TO-220
IRS21064S 2000 IR 14+ SOP14
L4981A 2000 ST 14+ SOP20
LD1117DT33TR 2000 ST 14+ TO252
LM317K 2000 UTC 16+ TO220
LM340MPX-5.0 2000 NS 16+ SOT-223
LM386MX-1 2000 NS 13+ SOP8
LPC2378FBD 2000 15+ QFP144
MAX3160EAP 2000 MAXIM 16+ SSOP20
MAX6902ETA 2000 MAXIM 16+ QFN
MC68HC11E1CFNE2 2000 FREESCAL 14+ PLCC-52
MJE15032G 2000 ON 14+ TO220
MOC3052 2000 FSC 14+ DIP6
MOC3063S 2000 FSC 16+ SOP-6
MOC8111M 2000 FAIRCHILD 16+ DIP-6
NCP1203D60 2000 ON 13+ SOP-8

 

 

 

 

 

 

Send RFQ
Stock:
MOQ:
10pcs