TS3USB221ARSER Ethernet Switch IC USB Switch ICs ESD Prot,Hi Spd USB 2.0 1:2 Mux/Demux Sw
fast ethernet switch chip
,ethernet controller ic
TS3USB221ARSER Ethernet Switch IC USB Switch ICs ESD Prot,Hi Spd USB 2.0 1:2 Mux/Demux Sw
1 Features
- VCC Operation at 2.5 V to 3.3 V
-
VI/O Accepts Signals Up to 5.5 V
-
1.8-V Compatible Control-Pin Inputs
-
Low-Power Mode When OE Is Disabled (1 μA)
-
RON = 6 Ω Maximum
-
ΔRON = 0.2 Ω Typical
-
Cio(on) = 6 pF Typical
-
Low Power Consumption (30 μA Maximum)
-
High Bandwidth (900 MHz Typical)
-
Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
-
ESD Performance Tested Per JESD 22
-
– 7000-V Human-Body Model (A114-B, Class II)
-
– 1000-V Charged-Device Model (C101)
-
-
ESD Performance I/O to GND – 12-kV Human-Body Model
2 Applications
-
Routes Signals for USB 1.0, 1.1, and 2.0
-
Mobile Phones
-
Cameras
-
Notebooks
3 Description
The TS3USB221A device is a high-bandwidth switch specially designed for the switching of high-speed USB 2.0 signals in handset and consumer applications, such as cell phones, digital cameras, and notebooks with hubs or controllers with limited USB I/Os. The wide bandwidth (900 MHz) of this switch allows signals to pass with minimum edge and phase distortion. The device multiplexes differential outputs from a USB host device to one of two corresponding outputs. The switch is bidirectional and offers little or no attenuation of the high-speed signals at the outputs. The device also has a low power mode that will reduce the power consumtion to 1 μA for portible applications with a battery or limited power budget. The device is designed for low bit-to- bit skew and high channel-to-channel noise isolation, and is compatible with various standards, such as high-speed USB 2.0 (480 Mbps).
The TS3USB221A device integrates ESD protection cells on all pins, is available in a tiny μQFN package (2 mm × 1.5 mm) and is characterized over the free air temperature range from –40°C to 85°C.
Device Information
|
PART NUMBER |
PACKAGE |
BODY SIZE (NOM) |
|
TS3USB221A |
UQFN |
1.50 mm × 2.00 mm |
W25N01GVZEIG SLC Nand Flash Memory IC 3V 1G BIT Winbond TW SPI
PF48F4400P0VBQEK NEW AND ORIGINAL STOCK
DSPIC30F3011-30I/PT Flash Memory IC NEW AND ORIGINAL STOCK
IR2110PBF NEW AND ORIGINAL STOCK
S25FL032P0XMFI010 SOP8 104MHz Flash Memory IC Chip
W25Q80DVSNIG Serial Flash Chip 3V 8M BIT Dual Quad Spi Memory Integrated Circuit
MOS Tube Field Effect Single-Chip Drive PWM Controlador Module IRF520
MAX485, RS485 Module TTL To RS-485 Module TTL To 485
SKY65336-11 NEW AND ORIGINAL STOCK
| Image | Part # | Description | |
|---|---|---|---|
|
|
W25N01GVZEIG SLC Nand Flash Memory IC 3V 1G BIT Winbond TW SPI |
FLASH - NAND (SLC) Memory IC 1Gbit SPI - Quad I/O 104 MHz 7 ns 8-WSON (8x6)
|
|
|
|
PF48F4400P0VBQEK NEW AND ORIGINAL STOCK |
FLASH - NOR (MLC) Memory IC 512Mbit CFI 52 MHz 110 ns 64-LBGA (11x13)
|
|
|
|
DSPIC30F3011-30I/PT Flash Memory IC NEW AND ORIGINAL STOCK |
dsPIC dsPIC™ 30F Microcontroller IC 16-Bit 30 MIPs 24KB (8K x 24) FLASH 44-TQFP (10x10)
|
|
|
|
IR2110PBF NEW AND ORIGINAL STOCK |
Half-Bridge Gate Driver IC Non-Inverting 14-DIP
|
|
|
|
S25FL032P0XMFI010 SOP8 104MHz Flash Memory IC Chip |
FLASH - NOR Memory IC 32Mbit SPI - Quad I/O 104 MHz 8-SOIC
|
|
|
|
W25Q80DVSNIG Serial Flash Chip 3V 8M BIT Dual Quad Spi Memory Integrated Circuit |
FLASH - NOR Memory IC 8Mbit SPI - Quad I/O 104 MHz 8-SOIC
|
|
|
|
MOS Tube Field Effect Single-Chip Drive PWM Controlador Module IRF520 |
N-Channel 100 V 9.2A (Tc) 60W (Tc) Through Hole TO-220AB
|
|
|
|
MAX485, RS485 Module TTL To RS-485 Module TTL To 485 |
1/1 Transceiver Half RS422, RS485 8-uMAX/uSOP
|
|
|
|
SKY65336-11 NEW AND ORIGINAL STOCK |
RF Front End 2.4GHz ISM 28-MCM (8x8)
|