TXS0101DCKR 3 State Programmable Logic ICS Open Drain BPort Signal Needed
programmable computer chip
,logic integrated circuits
TXS0101DCKR Programmable Logic ICS Voltage Levels 1B Bidirec Vltg- Lev Translator
1 Features
- Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II
- ESD Protection Exceeds JESD 22
- – APort
- – 2500 V Human-Body Model (A114-B)
- – 200 V Machine Model (A115-A)
- – 1500 V Charged-Device Model (C101)
- – BPort
- – 8 kV Human-Body Model (A114-B)
- – 200 V Machine Model (A115-A)
- – 1500 V Charged-Device Model (C101)
- No Direction-Control Signal Needed
- Maximum Data Rates
- – 24 Mbps (Push Pull)
- – 2 Mbps (Open Drain)
- Available in the Texas Instruments NanoFreeTM Package
- 1.65Vto3.6VonAportand2.3Vto5.5VonB port (VCCA ≤ VCCB)
- VCC Isolation Feature – If Either VCC Input Is at GND, Both Ports Are in the High-Impedance State
- No Power-Supply Sequencing Required – Either VCCA or VCCB Can be Ramped First
- Ioff Supports Partial-Power-Down Mode Operation
2 Applications
- Handsets
- Smartphones
- Tablets
- Desktop PCs
3 Description
This one-bit non-inverting translator uses two separate configurable power-supply rails. The A port is designed to track VCCA. VCCA accepts any supply voltage from 1.65 V to 3.6 V. The B port is designed to track VCCB. VCCA must be less than or equal to VCCB. VCCB accepts any supply voltage from 2.3 V to 5.5 V. This allows for low voltage bidirectional translation between any of the 1.8 V, 2.5 V, 3.3 V, and 5 V voltage nodes.
When the output-enable (OE) input is low, all outputs are placed in the high-impedance state.
To ensure the high-impedance state during power up or power down, OE should be tied to GND through a pull-down resistor; the minimum value of the resistor is determined by the current-sourcing capability of the driver.
Device Information
|
PART NUMBER |
PACKAGE |
BODY SIZE (NOM) |
|
TXS0101DBV |
SOT-23 (6) |
2.90 mm × 1.60 mm |
|
TXS0101DCK |
SC70 (6) |
2.00 mm × 1.25 mm |
|
TXS0101DRL |
SOT-5X3 (6) |
1.90 mm × 1.60 mm |
|
TXS0101YZP |
DSBGA (6) |
0.89 mm × 1.39 mm |
W25N01GVZEIG SLC Nand Flash Memory IC 3V 1G BIT Winbond TW SPI
PF48F4400P0VBQEK NEW AND ORIGINAL STOCK
DSPIC30F3011-30I/PT Flash Memory IC NEW AND ORIGINAL STOCK
IR2110PBF NEW AND ORIGINAL STOCK
S25FL032P0XMFI010 SOP8 104MHz Flash Memory IC Chip
W25Q80DVSNIG Serial Flash Chip 3V 8M BIT Dual Quad Spi Memory Integrated Circuit
MOS Tube Field Effect Single-Chip Drive PWM Controlador Module IRF520
MAX485, RS485 Module TTL To RS-485 Module TTL To 485
SKY65336-11 NEW AND ORIGINAL STOCK
| Image | Part # | Description | |
|---|---|---|---|
|
|
W25N01GVZEIG SLC Nand Flash Memory IC 3V 1G BIT Winbond TW SPI |
FLASH - NAND (SLC) Memory IC 1Gbit SPI - Quad I/O 104 MHz 7 ns 8-WSON (8x6)
|
|
|
|
PF48F4400P0VBQEK NEW AND ORIGINAL STOCK |
FLASH - NOR (MLC) Memory IC 512Mbit CFI 52 MHz 110 ns 64-LBGA (11x13)
|
|
|
|
DSPIC30F3011-30I/PT Flash Memory IC NEW AND ORIGINAL STOCK |
dsPIC dsPIC™ 30F Microcontroller IC 16-Bit 30 MIPs 24KB (8K x 24) FLASH 44-TQFP (10x10)
|
|
|
|
IR2110PBF NEW AND ORIGINAL STOCK |
Half-Bridge Gate Driver IC Non-Inverting 14-DIP
|
|
|
|
S25FL032P0XMFI010 SOP8 104MHz Flash Memory IC Chip |
FLASH - NOR Memory IC 32Mbit SPI - Quad I/O 104 MHz 8-SOIC
|
|
|
|
W25Q80DVSNIG Serial Flash Chip 3V 8M BIT Dual Quad Spi Memory Integrated Circuit |
FLASH - NOR Memory IC 8Mbit SPI - Quad I/O 104 MHz 8-SOIC
|
|
|
|
MOS Tube Field Effect Single-Chip Drive PWM Controlador Module IRF520 |
N-Channel 100 V 9.2A (Tc) 60W (Tc) Through Hole TO-220AB
|
|
|
|
MAX485, RS485 Module TTL To RS-485 Module TTL To 485 |
1/1 Transceiver Half RS422, RS485 8-uMAX/uSOP
|
|
|
|
SKY65336-11 NEW AND ORIGINAL STOCK |
RF Front End 2.4GHz ISM 28-MCM (8x8)
|