Quad-Channel Isolators with Integrated DC-to-DC Converter ADUM6402CRWZ
circuit board ic
,electronic components ic
FEATURES FUNCTIONAL BLOCK DIAGRAMS
isoPower integrated, isolated dc-to-dc converter
Regulated 3.3 V or 5 V output
Up to 500 mW output power
Quad dc-to-25 Mbps (NRZ) signal isolation channels
Schmitt trigger inputs
16-lead SOIC package with 7.6 mm creepage
High temperature operation: 105°C
High common-mode transient immunity: >25 kV/μs
Safety and regulatory approvals (pending)
UL recognition
5000 V rms for 1 minute per UL1577
CSA Component Acceptance Notice #5A
IEC 60950-1: 600 V rms (reinforced)
IEC 60601-1: 250 V rms (reinforced)
VDE certificate of conformity
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12
VIORM = 560 V peak
APPLICATIONS
RS-232/RS-422/RS-485 transceivers
Medical isolation
AC/dc power supply startup bias and gate drives
Isolated sensor interface
GENERAL DESCRIPTION
The ADuM640x1 devices are quad-channel digital isolators with
isoPower®, an integrated, isolated dc-to-dc converter. Based on
the Analog Devices, Inc., iCoupler® technology, the dc-to-dc
converter provides up to 500 mW of regulated, isolated power at
either 5.0 V or 3.3 V from a 5.0 V input supply, or 3.3 V from a
3.3 V supply at the power levels shown in Table 1. This eliminates
the need for a separate, isolated dc-to-dc converter in low power,
isolated designs. The iCoupler chip scale transformer technology
is used to isolate the logic signals and for the magnetic components
of the dc-to-dc converter. The result is a small form factor, total
isolation solution.
The ADuM640x isolators provide four independent isolation
channels in a variety of channel configurations and data rates
(see the Ordering Guide for more information).
isoPower uses high frequency switching elements to transfer
power through its transformer. Special care must be taken
during printed circuit board (PCB) layout to meet emissions
standards. Refer to the AN-0971 application note for board
layout recommendations at www.analog.com.
0402 0.063W 10kOhm SMT Thick Film Chip Resistor RC0402JR-0710KL
200MHz MPZ1608S300ATAH0 Chip Beads 5A For Power Line TDK SMD0603
22R 5% SMD0402 Film Chip Resistors ERJ-2GEJ220X PANASONIC
MOV-20D751K 750V 6.5kA Varistor blue SMD Chip Resistor 1 Circuit Through Hole Disc 20mm
2SB1261-TP 10W General Purpose Rectifier Diode Silicon Epitaxial Planar Pnp Transistor
IXFK140N30P Polar Power Mosfet Hiperfet TO264 300V 140A
DF2B29FU,H3F TVS 24VWM 47V ESD Protection Diodes
PMEG6010ER 1A Low VF MEGA Schottky Barrier Rectifier SOD123
SK34SMA 3A SMD Schottky Barrier Rectifier Diodes DO - 214AC
SMBJ5.0A Silicon Avalanche Diodes 600W Surface Mount TVS Diodes
Image | Part # | Description | |
---|---|---|---|
0402 0.063W 10kOhm SMT Thick Film Chip Resistor RC0402JR-0710KL |
10 kOhms ±5% 0.063W, 1/16W Chip Resistor 0402 (1005 Metric) Moisture Resistant Thick Film
|
||
200MHz MPZ1608S300ATAH0 Chip Beads 5A For Power Line TDK SMD0603 |
30 Ohms 1 Power Line Ferrite Bead 0603 (1608 Metric) 5A 10mOhm
|
||
22R 5% SMD0402 Film Chip Resistors ERJ-2GEJ220X PANASONIC |
22 Ohms ±5% 0.1W, 1/10W Chip Resistor 0402 (1005 Metric) Automotive AEC-Q200 Thick Film
|
||
MOV-20D751K 750V 6.5kA Varistor blue SMD Chip Resistor 1 Circuit Through Hole Disc 20mm |
750 V 6.5 kA Varistor 1 Circuit Through Hole Disc 20mm
|
||
2SB1261-TP 10W General Purpose Rectifier Diode Silicon Epitaxial Planar Pnp Transistor |
Bipolar (BJT) Transistor PNP 60 V 3 A 50MHz 1 W Surface Mount D-Pak
|
||
IXFK140N30P Polar Power Mosfet Hiperfet TO264 300V 140A |
N-Channel 300 V 140A (Tc) 1040W (Tc) Through Hole TO-264AA (IXFK)
|
||
DF2B29FU,H3F TVS 24VWM 47V ESD Protection Diodes |
47V Clamp 3A (8/20µs) Ipp Tvs Diode Surface Mount USC
|
||
PMEG6010ER 1A Low VF MEGA Schottky Barrier Rectifier SOD123 |
Diode 60 V 1A Surface Mount SOD-123W
|
||
SK34SMA 3A SMD Schottky Barrier Rectifier Diodes DO - 214AC |
Diode 40 V 3A Surface Mount DO-214AC, SMA
|
||
SMBJ5.0A Silicon Avalanche Diodes 600W Surface Mount TVS Diodes |
9.2V Clamp 65.3A Ipp Tvs Diode Surface Mount DO-214AA (SMBJ)
|