Send Message
Home > products > Power Management ICs > Programming Ethernet Jack electric circuit board STEF12PUR Enable / Fault functions

Programming Ethernet Jack electric circuit board STEF12PUR Enable / Fault functions

manufacturer:
Manufacturer
Description:
Electronic Fuse Regulator 3.6A 10-DFN (3x3)
Category:
Power Management ICs
Price:
Please contact me for details
Payment Method:
T/T, Western Union,Paypal
Specifications
Main Product Line:
IC,MODULE,TRANSISTOR,RESISTOR,DIODES,CAPACITOR
Voltage:
–0.3V To +10V
Temperature:
–65°C To +150°C
Package:
DFN-10
Payment Term:
T/T, Paypal,Western Union
Factory Pack:
REEL
Highlight:

programming ic chips

,

programmable audio chip

Introduction

 

 

Programming Ethernet Jack electric circuit board STEF12PUR Enable / Fault functions

 

STEF12PUR   

 

Electronic fuse for 12 V line

 

Features
 
■ Continuous current (typ): 3.6 A
■ N-channel on-resistance (typ): 53 mΩ
■ Enable/Fault functions
■ Output clamp voltage (typ):15 V
■ Undervoltage lockout
■ Short-circuit limit
■ Overload current limit
■ Controlled output voltage ramp
■ Thermal latch (typ): 165 °C
■ Uses tiny capacitors
■ Operating junction temp. - 40 °C to 125 °C
■ Available in DFN10 (3 x 3 mm) package
Applications
■ Hard disk drives
■ Solid state drives (SSD)
■ Hard disk and SSD arrays
■ Set-top boxes
■ DVD and Blu-Ray disc drivers
Description
The STEF12 is an integrated electronic fuse optimized for monitoring output current and input voltage. Connected in series to a 12 V rail, it is capable of protecting the electronic circuitry on its output from overcurrent and overvoltage. The device has a controlled delay and turn-on time. When an overload condition occurs, the STEF12 limits the output current to a predefined safe value. If the anomalous overload condition persists it goes into an open state, disconnecting the load from the power supply. If a continuous short-circuit is present on the board, when power is re-applied the E-fuse initially limits the output current to a safe value and then again goes into an open state. The device is equipped with a thermal protection circuit. The intervention of the thermal protection is signalled to the board monitoring circuits through a signal on the Fault pin. Unlike the mechanical fuses, which must be physically replaced after a single event, the Efuse does not degrade in its performance after short-circuit/thermal protection interventions and it is reset either by recycling the supply voltage or using the Enable pin. The companion chip for the 5 V power rails is also available with part number STEF05.

 

A part of stock list

TRANS STW34NM60ND ST 319 TO-247
C.I LF444CMX TI JC91AD/JC92AB SOP-14
DIODO STTH12R06D TI 315 TO-220AC
C.I UC3525ADWTR TI 5AZ129V SOP-16
C.I UC3845AD8TR TI 56MAOD6 SOP-8
C.I TC4423COE MICROCHIP 0838OTA SOP-16
C.I TC4424COE MICROCHIP 1209448 SOP-16
C.I SN74LVC06AD MICROCHIP 9AD6T5K SOP-14
DIODO 1N4756A SEMTECH SL0C2P0629Z200G/SL0C2P0509Z006G DO-41
C.I ICL7660CBAZ INTERSIL V1608BA SOP-8
C.I MM74HC164MX FSC P0548AD/PF8AD SOP-14
C.I SN74LS373N TI 62C068K DIP-20
C.I TL074CN TI 65A3QQM DIP-14
C.I DG529CJ INTERSIL 413 DIP-18
CAP 0603 1,5NF 50V X7R 5% 06035C152JAT2A AVX 1638 SMD0603
CAP 0805 10UF 16V X5R CL21A106KOQNNNE SAMSUNG ACAHOSH SMD0805
DIODO BAV99 1626/A7W SOT-23
C.I TLC072CDGNR TI TI4C/ADV MSOP-8
C.I LM2936Z-5,0 NSC 81AX TO-92
C.I TLC072CDGNR TI TI4C/ADV MSOP-8
C.I TL074CN TI 65A3QQM/67ALGQM DIP-14
C.I CD4093BM96 TI 1631+5/68AG96K SOP-14
C.I SN7407N TI 5CAQ63K DIP-14
BD9876EFJ-E2 ROHM 3472 HTSOP-8
LD1086V33 ST 833 TO-220
74LVC07AD 1607 SOP-14
CAT811STBI-GT3 ON VEAL SOT-143
ACOPLADOR 4N37 FSC 513Q DIP-6
C.I 74LVC04AD 1433 SOP-14
C.I 74LVC86AD 0303+ SOP-14
Send RFQ
Stock:
MOQ:
10 PCS